Ls pressure plate torque specs

Chevy Silverado 2 (2007-2014) Torque Spec Settings. Bull-Doser, Public domain, via Wikimedia Commons. Below you'll find the tightening torques for the Chevy Silverado 2 in both Nm and ft/lbs. The first table contains the most-used torque settings. The tables after it contain all torque spec values I could find.

Listed below are the general torque recommendations for bulk 5-packs and engine/accessory fasteners. Recommended torque is equal to 75% of the fastener's yield strength. Simply read down to the correct fastener size, then across to find the torque value for your application. Always use ARP Ultra-Torque ® and follow the instructions below to ...Enter your kit number in the field below and click “Submit.”. Important: if you have an aftermarket connecting rod with an ARP bolt, please use the chart below to contact the rod manufacturer for the stretch/torque value. The calculation of those values is solely up to the rod manufacturer. click here to contact our customer service desk.)Hi been thru a few posts, but chasing comformation as i dont wanna stuff it up.. New camed ls1 engine, t56 6speed. (Torque specs) Hd Flywheel/ clutch Hamonic balancer old bolt (then new) Manifold Water pump Cheers for any help, hopefully have the new engine in this w,end then off for a... the desired torque or the desired number of degrees during tightening, the wrench provides an audible beep. One handy feature of the Snap-On digital wrench is that you can tighten by ratcheting even during angle tightening. Several tool makers now offer digital torque/angle electronic torque wrenches. The bolt thread pitch on an LS flex plate is 1.5. The bolts are 11mm in diameter and are grade 8 steel. You can also find stronger aftermarket 12.9-grade bolts for an LS flex plate. Final Words. To summarize, the LS1, LS6, LS7, LS9, and LSA engines all have a 74 lb-ft torque spec for the flywheel bolts. Also, the sequence in which you … Plate to Case Bolt (Shipping) 20-25 lb ft : Plate to Converter Bolt (Shipping) 20-25 lb ft : Plug Assembly, Automatic Transmission Oil Pan (C/K) 22.1-29.5 lb ft : Plug Assembly, Automatic Transmission Oil Pan (Y) 20.7-23.6 lb ft : Pressure Control Solenoid Bracket to Valve Body Bolt : 6-10 lb ft : Pump Assembly to Case Bolt Pressure plate bolts are torqued in three phases, the torque specs are 20-40-52 ft/lbs of torque. The torque sequence is 1-4-6-2-5-3 IF YOUR CAR STILL HAS A FACTORY CLUTCH PEDAL ASSIST SPRING REMOVE IT BEFORE DRIVING, THIS WILL ALLOW A MORE LINEAR PEDAL FEEL AND WILL IMPROVE THE DRIVING …

Camshaft Position (CMP) Sensor to Engine Front Cover 9 Y 80 lb in Retaining Bolt. Camshaft Retainer to Engine Block Retaining Bolt 25 Y 18 lb ft. Camshaft Sprocket to Camshaft Retaining Bolt (L98, LS3, L76, L77) • First Pass 75 Y 55 lb ft. • Second Pass + 50 Degrees. Close Out Cover to Engine Block Retaining Bolt Left 10 Y …The oil pump assembly should be tightened down to the engine block using 18 ft-lbs. The pumps cover bolts can be installed after lubing up the oil pump gear. The oil pump cover bolts torque down to 8 ft-lbs. On the bottom end of the pump the pickup tube can be installed and torqued down to the pump using 8 ft-lbs.The Opel 2H0 is a 1.8 l (1,796 cc, 109.6 cu-in) straight-four four-stroke natural aspirated gasoline engine from the third generation of GM Family 1. This is the same engine as Opel A18XER. The 2H0 engine uses a cast grey iron block with five-bearings crankshaft and aluminum head with dual overhead camshafts (DOHC) and four valves per cylinder ...When it comes to optimizing the performance of your Kohler engine, one crucial factor that cannot be overlooked is the torque specifications. Torque specs refer to the specific amo...These torque specs were taken from International Harvester's Service Manual for a late model Scout II. This is meant to be a general guideline. Actual values may vary depending on specific models, please double check values for your specific application. General: Lug Nuts 90–110 ft⋅lbs Body Bolts 35–50 ft⋅lbs Brake Hos125 N·m. 92 lb ft. Cylinder Head Bolts (First Pass all M11 Bolts in Sequence) 30 N·m. 22 lb ft. Cylinder Head Bolts (Second Pass all M11 Bolts in Sequence) 90 degrees. Cylinder …

23667 posts · Joined 2007. #6 · Jul 9, 2011. the funny part, is i just picked up a suzuki ds185cc 2 stroke, and they actually listed "good and tight" as the torque value of some fasteners in the service manual. LOL. patprimmer said: Believe none of what you hear and half of what you see. Henry Ford said:Is the Spec flywheel steel, or aluminum? If it's aluminum, get specs right from Spec. I have seen too many pressure plates sripped out. I now helicoil all my aluminum flywheel installs. If the flywheel is stock or billet, disregard. LOL BTW, GM specs in TQ #'s are Flywheel bolts 1st pass 15 ft-lbs 2nd pass 37 ft-lbs 3rd pass 74 ft-lbs Pressure ...pressure plate bolt. Tighten all bolts evenly, ¼ turn at a time in a crisscross pattern until pressure plate is completely drawn-up to the fl ywheel. Final torque to: 35 - 38 ft/lbs. Note: These specifi cations apply only to the fasteners supplied by Centerforce. I01MI007 CENTERFORCE TECH. LINE (928) 771-8422 3/8” Pressure Plate BoltsTorque Spec: 7/16 in. Outer Main Cap Bolt: 65 ft.-lbs. 7/16 in. Inner Main Cap ... Pressure Plate Bolts: 35 ft.-lbs. Bellhousing Bolts: 25 ft.-lbs. Exhaust Manifold Bolts: 25 ft.-lbs. Notes. These specs are for stock-type bolts with light engine oil applied to the threads and the underside of the bolt head. Moly and other lubes offer reduced ...

Obituaries caribou maine.

The Opel 2H0 is a 1.8 l (1,796 cc, 109.6 cu-in) straight-four four-stroke natural aspirated gasoline engine from the third generation of GM Family 1. This is the same engine as Opel A18XER. The 2H0 engine uses a cast grey iron block with five-bearings crankshaft and aluminum head with dual overhead camshafts (DOHC) and four valves per cylinder ...24 kits found for Pressure Plate (Clutch Cover) Bolts. ARP offers High Performance Series bolts that are made from a premium grade chrome moly and hardened to a nominal tensile strength of 180,000 psi. The Pro Series bolts, originally developed for NASCAR competition, are rated at 200,000 psi. Both models feature a large diameter, low-profile ... GM7.5L-455ci-V8PONTIAC. GM Engine Torque Specs. Over 6,000 Automotive Torque Specs. Search Car Torque Specifications by Engine or Model. Cummins calls the adapter plate a “flywheel housing” and lists the torque spec as 57 ft/lbs. I’ll post the source file of this spec when I get back to my computer. …. -97 Dodge 2500 ext cab 4×4,, NV4500, the usual stuff with an SXE 362 . -2010 Ford F-250 4×4 w/ 180hp P-pump Cummins 12 valve, 5r110 auto, the usual stuff with an SXE 363.18 ft-lbs. A/C Compressor Torque Spec. 37 ft-lbs. 1500 5.3L engine bolt torque specs, common problems and repairs. Cylinder Head Torque specs, timing chain installation, manifolds torque specs, engine assembly.

The oil pump assembly should be tightened down to the engine block using 18 ft-lbs. The pumps cover bolts can be installed after lubing up the oil pump gear. The oil pump cover bolts torque down to 8 ft-lbs. On the bottom end of the pump the pickup tube can be installed and torqued down to the pump using 8 ft-lbs. What is the torque spec for the pressure plate to flywheel bolts? Should I use a hardended grade 8 bolts with a higher torque spec? I have heavily modified the engine, it is now a stroker 383, approx 450/450 hp/q, and running a Centerforce clutch.Oil Pressure Sensor 35Y 26lbft Oil Pump Cover to Oil Pump Retaining Bolt 12Y 106lbin Oil Pressure Relief Valve Plug to Oil Pump 14Y 124lbin Oil Pump Screen to Crankshaft Oil Deflector Retaining Nut 10Y 89lbin Oil Pump Screen to Oil Pump Retaining Bolt 9Y 80lbin Oil Pump to Engine Block Retaining Bolt 25Y 18lbft Spark Plug • Fit New Spark Plug ...The bolt thread pitch on an LS flex plate is 1.5. The bolts are 11mm in diameter and are grade 8 steel. You can also find stronger aftermarket 12.9-grade bolts for an LS flex plate. Final Words. To summarize, the LS1, LS6, LS7, LS9, and LSA engines all have a 74 lb-ft torque spec for the flywheel bolts. Also, the sequence in which you …343 posts · Joined 2008. #1 · Oct 29, 2009. Does anyone know of the 6 bolts that connect the pressure plate and the flywheel? Spec of the bolts or part number would work. Thanks. 95 TA, short shifter, msd: coil, distributor, 6AL, le3, lt4 intake, borla, mid-lenghts, underdrive, Soon to come: forged 383. Share.I am installing a new clutch, pressure plate and throw out bearing in a Chevy 350, 260 hp, street driven engine connected to a Muncie 4 speed transmission. Zoom, stock type clutch and pressure plate. I can not find torque specs in my service manual for the pressure plate.The 2011 Chevrolet Express van has the 6.0-liter engine as an option. The BBC gives the van a peak horsepower of 397 horsepower at 3,000 rpm and a peak torque of 765 pound-feet at 1,600 rpm. The GM 6.0 liter engine is featured on Chevrolet and GMC pickup trucks, vans, and SUVs. The big block Chevy (BBC) engine has the power to tow and carry a ...Chevy Silverado 2 (2007-2014) Torque Spec Settings. Bull-Doser, Public domain, via Wikimedia Commons. Below you'll find the tightening torques for the Chevy Silverado 2 in both Nm and ft/lbs. The first table contains the most-used torque settings. The tables after it contain all torque spec values I could find.When you build a spec home, you'll have to work with a mortgage lender. If you're a builder building a custom home for a client, that client will get a mortgage loan to pay you whi...5.3 Knock Sensor Plate Torque Specs The torque specifications for the 5.3 Knock Sensor Plate are 10 Nm (90 in-lbs) with a maximum torque of 15 Nm (135 in-lbs). It is important to ensure that these specifications are followed as too much or too little torque can cause damage to the plate and surrounding components, leading to costly repairs.Nov 9, 2008 · Flywheel installation: I recommend using new bolts for this. Install the flywheel bolts using a star pattern, and. then double-check them. Using the locator hole, orient the new one like the factory. flywheel. Flywheel torque sequence in star pattern: Step 1 20 Nm 15 lb ft. Step 2 50 Nm 37 lb ft.

J30-J32-J35 Honda V6/I4 J-Series Torque Specs CYLINDER HEAD V6 J30-J32-J35 & I4 TORQUE SPECS Cylinder Head Stud Bolts: Step 1: 29 ft lbs Step 2: 51 ft lbs Step 3: 72.3 ft lbs Camshaft thrust plate bolt: 16 ft lbs Camshaft sprocket bolts: 43 ft lbs Intake manifold nuts/bolts: 16ft lbs ... Clutch pressure plate bolts: 19 ft lbs. Flywheel to ...

The Opel 2H0 is a 1.8 l (1,796 cc, 109.6 cu-in) straight-four four-stroke natural aspirated gasoline engine from the third generation of GM Family 1. This is the same engine as Opel A18XER. The 2H0 engine uses a cast grey iron block with five-bearings crankshaft and aluminum head with dual overhead camshafts (DOHC) and four valves per cylinder ...Advertisement Starting at $1,199 for the 13-inch base model, the MacBook Pro's price point can vary quite a bit depending on your needs [source: Apple]. There are three screen size...Sep 25, 2023 · The LS flexplate torque specs vary based on the LS generations. For the third-generation LS engine, the torque has three passes: 15 lb-ft, 37 lb-ft, and 74 lb-ft. For most fourth-gen, the torque is 22 lb-ft. LS Flexplate Bolt Torque And Size. The LS flex plate torque/ flywheel bolt torque specs vary depending on the engine generation and design. 14946 posts · Joined 2007. #1 · Dec 27, 2013. What are you guys torquing your PP bolts to? I just threw on a clutchmasters billet steel flywheel. I have been finding conflicting information about torque specs ranging from 20-40 ft lbs. Like.I also welcome you to add to the list, or edit any mistakes that I may have listed. The following specs are for my 2006 Aveo LT Hatchback 5-speed... but I'm sure it crosses over to a lot of models... Cylinder head bolts 18 ft lbs, 60⁰, 60⁰, 60⁰, 10⁰. Main bearing bolts 37 ft lbs, 45⁰, 15⁰. Rod bearing bolts 18 ft lbs, 30⁰, 15⁰.Buying a HDTV is hard enough with so many different manufactures, model numbers, and sizes, to make things a little easier we've put together a list of the most common specificatio...May 5, 2022 · While working on your vehicle, make sure to tighten all bolts evenly. A ¼ turn at a time in a crisscross pattern works best for drawing-up the pressure plate to the flywheel. Make sure the final torque is between 35 - 38 ft/lbs so that it is properly secured and won't come loose while you are driving. If done correctly, this should ensure that ... Pressure plate bolts are torqued in three phases, the torque specs are 20-40-52 ft/lbs of torque. The torque sequence is 1-4-6-2-5-3 IF YOUR CAR STILL HAS A FACTORY CLUTCH PEDAL ASSIST SPRING REMOVE IT BEFORE DRIVING, THIS WILL ALLOW A MORE LINEAR PEDAL FEEL AND WILL IMPROVE THE DRIVING …The Nm and lb-ft are off column so read it as 33 + 60° for lb-ft. Torque Specifications. Description Nm lb-ft. Pressure plate to flywheel bolt (3.8L) 33 24. Pressure plate to flywheel bolts 4.6L (2V) 45 + 60° 33 + 60°. Pressure plate-to-flywheel bolts 4.6L (4V) 45 + 60° 33 + 60°. Last edited: Oct 2, 2021.These specs are for stock-type bolts with light engine oil applied to the threads and the underside of the bolt head. Moly and other lubes offer reduced friction and increased bolt tension, which will affect the torque figure. If you use aftermarket performance bolts like ARP's, you should follow the recommended torque specifications.

Chris elwood wikipedia.

Pawn 1 hillyard.

Alternator Rear Bracket Torque Spec. 18 ft-lbs. A/C Compressor Torque Spec. 37 ft-lbs. 2500 6.0L engine bolt torque specs, common problems and repairs. Cylinder Head Torque specs, timing chain installation, manifolds torque specs, engine assembly.The oil pump assembly should be tightened down to the engine block using 18 ft-lbs. The pumps cover bolts can be installed after lubing up the oil pump gear. The oil pump cover bolts torque down to 8 ft-lbs. On the bottom end of the pump the pickup tube can be installed and torqued down to the pump using 8 ft-lbs.The LS flexplate torque specs vary based on the LS generations. For the third-generation LS engine, the torque has three passes: 15 lb-ft, 37 lb-ft, and 74 lb-ft. For most fourth-gen, the torque is 22 lb-ft. LS Flexplate Bolt Torque And Size. The LS flex plate torque/ flywheel bolt torque specs vary depending on the engine generation and …Get The Right BBC Engine Specs With JEGS. Are you trying to nail down the right torque specs for a big block Chevy engine? JEGS can help. We have a great selection of engines and parts in stock, such as the Blueprint Crate Engines Big Block Chevy (496ci 575HP / 600TQ) or ATK HP Crate Engines Big Block Chevy (489ci / …LS Fastener Torque Specifications. Applying the correct tightening values for threaded engine fasteners is critical for any engine build. Listed here are both factory OEM values, some of which involve a torque-plus-angle tightening method, and OEM and aftermarket values which require only a tightening-by-torque (or by monitoring rod bolt ...135 posts · Joined 2013. #1 · Nov 16, 2022. it seems theres little to no info on the correct torque specs on a 2009 chally R/T 6m . im replacing my clutch with a new flywheel and pressure plate im pretty sure the tq on flywheel is 55 i ave also read same on pressure plate (55) . my concern is 55 ft lbs on pressure plate seems way to high for ...The LS flexplate torque specs vary based on the LS generations. For the third-generation LS engine, the torque has three passes: 15 lb-ft, 37 lb-ft, and 74 lb-ft. For most fourth-gen, the torque is 22 lb-ft. LS Flexplate Bolt Torque And Size. The LS flex plate torque/ flywheel bolt torque specs vary depending on the engine generation and design.Is the Spec flywheel steel, or aluminum? If it's aluminum, get specs right from Spec. I have seen too many pressure plates sripped out. I now helicoil all my aluminum flywheel installs. If the flywheel is stock or billet, disregard. LOL BTW, GM specs in TQ #'s are Flywheel bolts 1st pass 15 ft-lbs 2nd pass 37 ft-lbs 3rd pass 74 ft-lbs Pressure ...Chevrolet LS Gen. 3, Aluminum Block Torque Specs. Views: The following specs apply to RPO codes: LS1. LS6. LM4. L33. **Click the blue links in the table for more detailed …Anyway, the torque specs: Flywheel to crank: 89 lb-ft. Pressure Plate to flywheel: 19-26 lb-ft. Cheers! 97 F250 SC 4x4 (CA model), E4OD, 4.10 LS, Relocated Block Heater Plug, Ext Trans Filter, Tru-Cool Max, I/C Mounted but not Plumbed. SOLD: 94 F350 CC DRW, 5 Speed, SBC Con-O, Baldwin Filter, Tymar HPX Hose, 3” DP, Bilsteins, $12 … ….

Learn everything you need to know about spec homes in The Homeowner's Guide. Get insights on the buying process, financing options, and more. Click to read now. Expert Advice On Im... The oil pump assembly should be tightened down to the engine block using 18 ft-lbs. The pumps cover bolts can be installed after lubing up the oil pump gear. The oil pump cover bolts torque down to 8 ft-lbs. On the bottom end of the pump the pickup tube can be installed and torqued down to the pump using 8 ft-lbs. Fastener Tightening Specifications Application Specification Metric English Clutch Actuator Cylinder Mounting Bolts 12 N·m 106 lb in Clutch Pedal Bracket Mounting Nuts 27 N·m 20 lb ft Clutch Pedal Nut 50 N·m 37 lb ft Clutch Pressure Plate Bolts¹ 70 N·m 52 lb ft Cruise Control Release Switch Bracket Retaining Bolts 12 N·m 106 lb inInstall the pressure plate attaching the bolts finger tight and then tightening progressively around the pattern to the following: 5/16”- 25 to 30 ft./lbs. torque maximum 3/8”- 30 to 40 ft./lbs. torque maximum 7. Remove lever blocks only after pressure plate is torqued to flywheel. They are located between the levers and the cover.Oil Pressure Sensor 35Y 26lbft Oil Pump Cover Bolts 12Y 106lbin Oil Pump Relief Valve Plug 12Y 106lbin Oil Pump Screen Nuts 25Y 18lbft Oil Pump Screen-to-Oil Pump Bolt 12Y 106lbin Oil Pump-to-Engine Block Bolts 25Y 18lbft Oil Temperature Sensor 20Y 15lbft Power Steering Pump Bolt 25Y 18lbft Propeller Shaft Hub Collar Bolt 125Y 92lbftTo find out a wheel torque spec, check the vehicle’s manual, industry reference guide or the shop repair manual. Vehicle dealers can also provide an appropriate wheel torque spec. ... Enter your kit number in the field below and click “Submit.”. Important: if you have an aftermarket connecting rod with an ARP bolt, please use the chart below to contact the rod manufacturer for the stretch/torque value. The calculation of those values is solely up to the rod manufacturer. click here to contact our customer service desk.) The Super Twin is for street and track use in cars with extreme horsepower and torque (700-1500 ft lbs tq). The Super Twin offers near-stock drivability, tremendous life expectancy, a no-shimming/setup bolt-in installation and maintenance free operation. ... SPEC Super Clamp pressure plates have extreme clamp loads that are beyond what is ...RAM Pressure Plates - Design your own Clutch System. RAM performance pressure plates are engineered and built to meet the demands of high horsepower street and competition cars and trucks. ... 2800 pound clampload exc. LS. PART NO. 402. DESC. 11" GM LS, 2800 pound clampload. ... See pressure plates specifications. BORG & … Ls pressure plate torque specs, Fastener Tightening Specifications Application Specification Metric English Camshaft Position(CMP) Sensor Bolt 12Y 106lbin CMP Sensor Wire Harness Bolt 12Y 106lbin Camshaft Retainer Bolts – Hex Head Bolts 25Y 18lbft Camshaft Retainer Bolts – TORX® Head Bolts 15Y 11lbft Camshaft Sprocket Bolts 25Y 18lbft Clutch Pressure Plate Bolts 70Y 52lbft, The oil pump assembly should be tightened down to the engine block using 18 ft-lbs. The pumps cover bolts can be installed after lubing up the oil pump gear. The oil pump cover bolts torque down to 8 ft-lbs. On the bottom end of the pump the pickup tube can be installed and torqued down to the pump using 8 ft-lbs., The oil pump assembly should be tightened down to the engine block using 18 ft-lbs. The pumps cover bolts can be installed after lubing up the oil pump gear. The oil pump cover bolts torque down to 8 ft-lbs. On the bottom end of the pump the pickup tube can be installed and torqued down to the pump using 8 ft-lbs., When you go to install the engine into the vehicle or if it is already in the vehicle the torque specs for the exhaust manifold to the exhaust pipes or catalytic converter is 26 ft-lbs. The EGR system consists of a series of pipes that range from the manifold to the head. The EGR pipes can be torqued down to 22 ft-lbs., Look it up on a chart to determine if the torque spec matches the dry or lubricated column then apply the factor loctite recommends at the link above if the …, I also welcome you to add to the list, or edit any mistakes that I may have listed. The following specs are for my 2006 Aveo LT Hatchback 5-speed... but I'm sure it crosses over to a lot of models... Cylinder head bolts 18 ft lbs, 60⁰, 60⁰, 60⁰, 10⁰. Main bearing bolts 37 ft lbs, 45⁰, 15⁰. Rod bearing bolts 18 ft lbs, 30⁰, 15⁰., Hardware torque specifications for GM's 4L60E automatic transmission. Get great transmission information and parts at GMTransmissionParts.com. ... Friction Module & Clutch Plates Gaskets, Seals & O-Rings Pistons ... Pressure Control Solenoid to Valve Body Bolt: 1 : M6. 1.0 x 17.7 . 11 N-m. 8 lb-ft . Parking Brake Bracket to Case Bolt: 2 : M8., When you go to install the engine into the vehicle or if it is already in the vehicle the torque specs for the exhaust manifold to the exhaust pipes or catalytic converter is 26 ft-lbs. The EGR system consists of a series of pipes that range from the manifold to the head. The EGR pipes can be torqued down to 22 ft-lbs., Aug 29, 2022 · The 5.3 liter LS-series engine was offered from 1999-2014 and has a 3.78” bore x 3.62” stroke. The block was offered in both cast-iron and aluminum with aluminum cylinder heads. Camshaft specifications varied depending on the year and RPO code of the engine. , 18 ft-lbs. A/C Compressor Torque Spec. 37 ft-lbs. 1500 5.3L engine bolt torque specs, common problems and repairs. Cylinder Head Torque specs, timing chain installation, manifolds torque specs, engine assembly., 18-22 FT/LB. Differential Drain (24mm) 29-40 FT/LB. Differential Fill (23mm) 29-40 FT/LB. 1990-2005 Miata Torque Specs List. A full list of External Engine, Transmission, and Differential Torque Specs. Torque Specs are …, Pressure Plate to flywheel bolts torque to 15ft-lbs and aditional 30 degrees. Thats for six-speeds through 1999. 2000 and later is 52ft-lbs., Engine Oil Pressure Sensor 35Y (26lbft) Engine Wiring Harness Bolt(Rear Engine Channel) 10Y (89lbin) Engine Wiring Harness Jumper Bracket Bolt 25Y (18lbft) Evaporative Emission Canister Purge Solenoid Valve Bolt 10Y (89lbin) Flywheel Inspection Cover Bolt 10Y (89lbin) Flex Plate to Torque Converter Fastener 60Y (44lbft), RAM Pressure Plates - Design your own Clutch System. RAM performance pressure plates are engineered and built to meet the demands of high horsepower street and competition cars and trucks. ... 2800 pound clampload exc. LS. PART NO. 402. DESC. 11" GM LS, 2800 pound clampload. ... See pressure plates specifications. BORG & …, Object moved to here., When installing the oil pump be sure to use the proper sealant around the pump base if neccessary to ensure that oil pressure doesn't drop due to leakage. Both surfaces should be cleaned and preped prior to installing. ... Chevy Equinox 2.4L Water Pump Access Plate Torque Specs : 8 ft-lbs, The flywheel bolts are tightened in 3 steps. First tighten to 58 ft. lb. Second, tighten all bolts 60 degrees. Third, tighten all bolts an additional 60 degrees. Use the torque sequence shown in the picture below. The pressure plate bolts are tightened to 52 ft. lb. in the sequence in the picture below. Dave Nova., Over 6,000 Automotive Torque Specs. Search Car Torque Specifications by Engine or Model. TorkSpec. How it works; Rides; Projects; FAQ; Sign in or Sign up. Automotive Engine Torque Specs Torque Specifications for GM 5.7L ... Pressure Plate To Flywheel. 35 Ft-Lbs. 420 In-Lbs. 47.45 N-m. Years: All. Note: Chevy Small Block. Type: Dim: …, Pressure plate bolts are torqued in three phases, the torque specs are 20-40-52 ft/lbs of torque. The torque sequence is 1-4-6-2-5-3 IF YOUR CAR STILL HAS A FACTORY CLUTCH PEDAL ASSIST SPRING REMOVE IT BEFORE DRIVING, THIS WILL ALLOW A MORE LINEAR PEDAL FEEL AND WILL IMPROVE THE DRIVING CHARACTERISTICS OF THE UNIT., GM Lifter Tray / Guide for GM LS-Series Engines, each, Part #12595365 Tick Performance Slave Cylinder Shim Kit (3 Pack) GM Slave Cylinder & Throwout / Release Bearing for 1998-02 Camaro & Firebird LS1, Part #24264182, Chevy Silverado 1 (1998-2006) Torque Spec Settings. IFCAR, Public domain, via Wikimedia Commons. Below you'll find the tightening torques for the Chevy Silverado 1 in both Nm and ft/lbs. The first table contains the most-used torque settings. The tables after it contain all torque spec values I could find. , 14946 posts · Joined 2007. #1 · Dec 27, 2013. What are you guys torquing your PP bolts to? I just threw on a clutchmasters billet steel flywheel. I have been finding conflicting information about torque specs ranging from 20-40 ft lbs. Like., The 2011 Chevrolet Express van has the 6.0-liter engine as an option. The BBC gives the van a peak horsepower of 397 horsepower at 3,000 rpm and a peak torque of 765 pound-feet at 1,600 rpm. The GM 6.0 liter engine is featured on Chevrolet and GMC pickup trucks, vans, and SUVs. The big block Chevy (BBC) engine has the power to tow and carry a ..., 125 N·m. 92 lb ft. Cylinder Head Bolts (First Pass all M11 Bolts in Sequence) 30 N·m. 22 lb ft. Cylinder Head Bolts (Second Pass all M11 Bolts in Sequence) 90 degrees. Cylinder …, A/C Compressor Bolt Torque Spec (Rear) 37 ft-lbs. A/C Compressor Bolt Torque Spec (Front) 17 ft-lbs. camaro 3.6L engine bolt torque specs, common problems and repairs. Cylinder Head Torque specs, timing chain installation, …, HE-05191. Chevrolet LS Gen. 4 Aluminum Block Torque Specs. The following specs apply to RPO codes: LS2. LS3. LS4. LH6. LC9. L92. Etc. **Click the blue links in the table for …, The generic torque specification for a new 5/16-18 grade 5 bolt is 17 lb-ft dry, 10 lb-ft oiled so we are talking little more than screwdriver tight. In other words you don't need a big honkin wrench. ... But in the 50+ years I've worked on machinery I have NEVER felt the need for a torque wrench to tighten pressure plate bolts. Or most other ..., Torque: Camshaft Retainer Bolts: 18 lb ft: Camshaft Sensor Bolt: 18 lb ft: Camshaft Sprocket Bolts: 26 lb ft: Connecting Rod Bolts - First Design (First Pass) 15 lb ft: Connecting Rod Bolts - First Design (Final Pass) 60 degrees: Connecting Rod Bolts - Second Design (First Pass) 15 lb ft: Connecting Rod Bolts - Second Design (Final Pass) 75 degrees, Pressure plate bolts are torqued in three phases, the torque specs are 20-40-52 ft/lbs of torque. The torque sequence is 1-4-6-2-5-3 IF YOUR CAR STILL HAS A FACTORY CLUTCH PEDAL ASSIST SPRING REMOVE IT BEFORE DRIVING, THIS WILL ALLOW A MORE LINEAR PEDAL FEEL AND WILL IMPROVE THE DRIVING …, Anyway, the torque specs: Flywheel to crank: 89 lb-ft. Pressure Plate to flywheel: 19-26 lb-ft. Cheers! 97 F250 SC 4x4 (CA model), E4OD, 4.10 LS, Relocated Block Heater Plug, Ext Trans Filter, Tru-Cool Max, I/C Mounted but not Plumbed. SOLD: 94 F350 CC DRW, 5 Speed, SBC Con-O, Baldwin Filter, Tymar HPX Hose, 3” DP, Bilsteins, $12 …, Jul 25, 2008 · Is the Spec flywheel steel, or aluminum? If it's aluminum, get specs right from Spec. I have seen too many pressure plates sripped out. I now helicoil all my aluminum flywheel installs. If the flywheel is stock or billet, disregard. LOL BTW, GM specs in TQ #'s are Flywheel bolts 1st pass 15 ft-lbs 2nd pass 37 ft-lbs 3rd pass 74 ft-lbs Pressure ... , Oil is especially interesting as it is deemed the cheapest. Cheap is cheap for a reason. Since the start of the year, all investors have been inundated by calls to buy the value st..., The tables after it contain all torque spec values I could find. Most-used torque settings for Ford Super Duty 1. ... Clutch pressure plate bolt: 45: 33: 5.4L Engine;